Connectors car amplifier molex six iso#

Minor connector B has 12 pins for audio output signals. 3 Pin Miniature Nylon MOLEX-Type Connector CAT.NO: PP2023 These connectors are suitable for high current/high density, wire-to-wire or wire-to-board applications. They fit within the frame of the main connector, and have coding so that they cannot be interchanged.

Connectors car amplifier molex six iso#

In addition to the 16 pins, like ISO 10487, there are minor connectors for optional equipment. While the physical contact pins are the same, the pin allocation is not entirely the same, and the connector housing is not compatible. The Quadlock connector consists of a block of 16 flat pins analogous to the two main ISO 10487 connectors. Therefore, searching for Quadlock components may be unsuccessful for example, Molex refers to a typical component of the connector as MOST Frame Receptacle Housing (part number 986811001). Unfortunately, Quadlock may not be the description used by manufacturers of the connector components. It has ten pins.įrom 2000 and onwards, manufacturers, such as BMW, Citroën, Ford, Mercedes Benz, Peugeot, Volkswagen, Rover, Audi, SEAT, Opel or Škoda have sometimes started using a 40-pin connector instead, called the Quadlock. The connector D is for satellite navigation systems. You may not need everything though depending on what you have. To follow along with this tutorial, you will need the following materials. The example above is oriented towards VW vehicles only. In this tutorial, we will replace the power supplys molex connector with two male barrel jacks adapters. Note: ISO 10487 only defines the physical attributes of the connectors, not the pin/signal designations, which are manufacturer-defined. The contact spacing is narrower than the other connectors, so the C connector is sometimes referred to as mini-ISO. Sometimes it appears as one 20-pin connector, often red in colour, or it may be divided into three separate connectors which may be hooked together, in which case C1 is usually yellow, C2 is typically green and C3 is generally blue in colour. And the best part is that you don’t need to be an expert to complete it.

However, if you’re a music enthusiast who wants to give your car’s audio system a boost, installing a 4-channel amplifier is an excellent option. The second connector B is for connecting four loudspeakers, front, rear, left and right, and is usually brown in colour.Ĭonnector C is optional. Many people believe that putting an amplifier in their car is too difficult and should only be done by a professional. Pin 6 is optional used for vehicle instrument illumination.Pin 3 is optional used for reversing lamp signal on Becker radios with navigation.Pin 1 is optional used for speed-dependent volume control and possibly navigation.On some cars the +12V Ignition and Battery positions are reversed, such as later Volkswagen Group cars, Peugeot 106, Vauxhall Astra, Citroën C3 and some JCB tractors.The first connector A is always present, is usually black in colour, and contains pins for power supply, off/on (typically controlled by the ignition key), optional control for a motorised antenna and so on. Part 1 of the standard is dedicated to 'Dimensions and general requirements' and Part 2 to 'Performance requirements'. ISO 10487 connector pinout (plug side of male, wiring side of female) Parts Steering Wheel Controls, SWC or Key, brown with black stripe, usually employs CAN bus.Back view, orange with white strip, works when reverse gear light is on, and it is used to turn on the back camera screen (i.e.Phone: the cable to mute when receiving a call is brown. A six-channel amplifier has six dedicated outputs.Amplifier remote turn on: blue with white stripe.They have low electric current, which is activated when the radio is turned on. Wires with black stripes are for negative power: as GND ( black), 0V, usually connected to the vehicle's metal chassis and body. Illumination ( orange with white stripe) or dimmer, when it is night and cars lights are turned on, head unit screen illumination is dimmed.This allows the radio to retain settings (for example, stored radio stations) when the ignition is switched off. Constant ( yellow), also called BAT or Battery, provides permanent +12V power from battery.ACC ( red), supplies +12V power to car audio and other accessories, only when the car's ignition is switched on.Splicing wires used in car audio are mainly for power, ground, amplifier and antenna, speakers, phone and others.